Features and Benefits
- Transmits up to 2 km over optical fiber
- Converts CAN signals to fiber and fiber to CAN signals
- Baudrate up to 1 Mbps
- Dual power inputs for redundancy
- DIP switch for 120 Ω terminal resistance
- DIP switch for fiber test mode
- LEDs for Fiber TX, Fiber RX, Power 1, Power 2
- Wide temperature model available for -40 to 85°C environments
- Fully compatible with the ISO 11898 standard
Introduction
The ICF-1170I series CANbus-to-fiber converters are used to convert CAN signals from copper to optical fiber. The converters come with 2 KV optical isolation for the CANbus system and dual power inputs with alarm contact relay to ensure that your CANbus system will remain online.
Fiber Test Mode
Fiber Test Mode can be used to test the fiber cable between two ICF-1170I units, and provides a simple way to determine if the fiber cable is transmitting data correctly. When in Fiber Test Mode, the fiber transceiver (TX) will continuously send out a data signal and the ”Fiber TX” LED will light up. On the other side of the connection, when the ICF-1170I fiber transceiver (RX) receives the data signal form the TX side, the ”Fiber RX” LED will light up.
• CAN Communication | |
CAN Interface | ISO 11898-2, Terminals (CAN_H, CAN_L,CAN_GND) |
Protocols | CAN 2.0A and 2.0B (ISO 11898-2) |
Connector Type | 3-pin removable screw terminal x1 |
Termination Resistor | Dip switch selector for 120 Ω terminal resistor |
Transfer Rate | Up to 1 Mbps |
System Delay | 150 ns |
Isolation Protection | 2 KV |
ESD Protection | Supports 15 KV |
Transmission Distance | Max 2 km (depends on the data rate and the protocol used) |
Note | The transmission distance is limited by the signal rate, as indicated in the ISO 11898-2 standard. |
LED Indicators | PWR1, PWR2, Fiber TX, Fiber RX |
• Fiber Communication | |
Connector Type | ST (multi-mode) fiber ports |
Support Cable | 50/125, 62.5/125, or 100/140 μm (multi-mode) |
Wavelength | 850 nm |
TX Output | Multi-mode (> -5 dBm) |
Rx Sensitivity | Multi-mode (-20 dBm) |
• Physical Characteristics | |
Housing | Aluminum (1 mm) |
Dimensions | 30.3 x 70 x 115 mm (1.19 x 2.76 x 4.53 in) |
Weight | Product only: 175 g (0.39 lb) Packaged: 320 g (0.71 lb) |
• Environmental Limits | |
Operating Temperature | Standard Models: 0 to 60°C (32 to 140°F) Wide Temp. Models: -40 to 85°C (-40 to 185°F) |
Storage Temperature | -40 to 85°C (-40 to 185°F) |
Ambient Relative Humidity | 5 to 95% (non-condensing) |
• Power Requirements | |
Input Voltage | 12 to 48 VDC dual power inputs for redundant power |
Power Consumption | ICF-1170I: 221 mA @ 12 V Alarm Contact: 1 relay output with current carrying of 1 A @ 24 VDC |
Voltage Reversal Protection | Protects against V+/V- reversal |
Over Current Protection | 1.1 A (protects against two signals shorted together) |
• Standards and Certifications | |
Safety | UL 508, EN 60950-1 |
EMC | CE, FCC |
EMI | EN 55022 Class A, FCC Part 15 Subpart B Class A |
EMS | EN 61000-4-2 (ESD) Level 4, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 4, EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 (PFMF) Level 3 |
Freefall | IEC 60068-2-32 |
Green Product | RoHS, CRoHS, WEEE |
• MTBF (mean time between failures) | |
Time | 792,085 hrs |
Database | Telcordia (Bellcore), GB |
• Warranty | |
Warranty Period | 5 years |
Details | See http://www.moxa.com/support/warranty.htm |